mcDSA-E35-PROFINET-HC
Article number: 1514997 Category: Servo amplifier Certification: UL *1 ![]() |
![]() Picture similar |
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
Features
- Motor controller up to 80A
- Compact four-quadrant controller for: DC motors, BLDC motors, Linear motors
- PROFINET interface
- CAN interface (Protocol DS301, Device profile DS402)
- integrated digital inputs
- integrated digital outputs
- integrated analog inputs
- Overvoltage, undervoltage and overtemperature monitoring
- Device status notification with the help of 3 LEDs (Power, Status, Error)
- Hex switches to set the device node id
- Easily programmable due to built-in MPU (Motion Process Unit)
Technical data
Name | Value |
---|---|
Absolute maximum rating (destruction limits) | |
- Power supply voltage Up
no polarity reversal protection |
80 V |
- Continuous Electronic supply voltage Ue
no polarity reversal protection |
33 V |
- Short term peak voltage < 1s Ue
no polarity reversal protection |
37 V |
Power | |
- Electronic supply voltage Ue | 18..30 V |
- Power supply voltage Up | 9..60 V |
- Max. output current | 80 A |
- Continuous output current (certified UL)*2 @Up ≤ 60V |
22.6 A |
- Continuous output current (not certified)*3 @Up ≤ 24V @Up ≤ 48V |
25 A 24 A |
PWM | |
- Output voltage | 90% Up |
- PWM frequency | 25, 32*4, 50 kHz |
- PWM mode | symmetrical / asymmetrical |
Motor types | |
- DC motors | yes |
- BLDC motors | yes |
- Linear motors | yes |
- Stepper motors | no |
Mechanical | |
- Size LxWxH | 87 x 74 x 49 mm |
CAN bus | |
- Protocol | DS301 |
- Device profile | DS402 |
- Galvanically isolated | no |
Sensor supply (Hall) | |
- Output voltage | 5 V |
- Max. output current | 0.05 A |
PROFINET | |
- Type | Slave |
- Physical layer | 100 Base-Tx |
- Max. baudrate | 100 Mbit/s |
- Number of ports | 2xRJ45 (PORT1, PORT2) |
Sensor supply (Encoder) | |
- Output voltage | 5 V |
- Max. output current | 0.2 A |
Incremental encoder | |
- Type | incremental |
- Input voltage | 0..5 V |
- Signal type | differential, open collector, single ended |
Hall sensors | |
- Input voltage | 0..5 V |
- Signal type | open collector, single ended |
Digital inputs | |
- Number - digital inputs | 8 (Din0..7) |
Digital outputs | |
- Number | 3 (Dout0..2) |
- Continuous output current (certified UL) | 1 A |
- Continuous output current (not certified) | 1.5 A |
- Load Dout0..1 | resistive, low inductive |
- Load Dout2 | resistive, inductive |
Analog inputs | |
- Number | 1 (Ain0) |
- Signal type - Ain | +/- 10 V, 12 Bit, differential |
Modifications and errors excepted.
*1 The certified performance data must be observed (see UL Instruction Note)
*2 connector cable with max. possible cable cross-section, PWM frequency 32 kHz (asymmetrical), ambient temperature 40 °C, I/O's and 5V output active, RMS current: 22.6 A → 18.5 Aeff
*3 connector cable with max. possible cable cross-section, PWM frequency 32 kHz (asymmetrical), ambient temperature 40 °C, I/O's and 5V output free, RMS current: 25 A → 20.4 Aeff, 24 A → 19.5 Aeff
no guarantee, since value is determined empirical, please consider the application notes to determine the continuous current
*4 default value
Cross references
- mcDSA-E30
- mcDSA-E30-HC
- mcDSA-E30-Lp
- mcDSA-E30-Modul-HC
- mcDSA-E30-Modul
- mcDSA-E32
- mcDSA-E32-HC
- mcDSA-E32-Lp
- mcDSA-E32-Modul-HC
- mcDSA-E32-Modul
- mcDSA-E35
- mcDSA-E35-EtherCAT-HC
- mcDSA-E35-EtherCAT
- mcDSA-E35-HC
- mcDSA-E35-Lp
- mcDSA-E35-Modul-HC
- mcDSA-E35-Modul
- mcDSA-E35-PROFINET
- mcDSA-E37
- mcDSA-E37-EtherCAT-HC
- mcDSA-E37-EtherCAT
- mcDSA-E37-HC
- mcDSA-E37-Lp
- mcDSA-E37-Modul-HC
- mcDSA-E37-Modul
- mcDSA-E37-PROFINET-HC
- mcDSA-E37-PROFINET
Devices from the same family:
Downloads
- Data sheet: mcDSA-E35-PROFINET-HC_en.pdf
- Documentation: mcManual
- 2D, 3D drawings: mcDSA-E35-PROFINET-HC-UL.zip
- Configuration software: mPLC Setup
Document Actions